Honing ye mun lo ye?
limɔgɔye baara laban cogo tilennin ye min kɔnɔ .kabakuruw(min be weele ko honing minanw) be kɛ ka fɛɛn dɔɔni bɔ baarakɛminɛn dɔ sanfɛ, a ka ca a la, a be kɛ yɔrɔ dɔ kɔnɔ min be kɛ ni silindiri ye.
Laɲinita ye ka .ka yɔrɔ sanfɛla labɛncogo fisaya, ka geometri latilen (a koorinin, a ka yɛlɛma, a ka tilen), ani ka jateminɛli tiɲɛtigiya sɔrɔ.
A ka ca a la, a be kɛ i n’a fɔ .tagamacogo labansɔgɔli, sɔgɔli, walima sɔgɔli kɔfɛ n’a ka ɲi ka yɔrɔw sɛgɛsɛgɛ ka ɲɛ ani k’u yɔrɔw sɛgɛsɛgɛ ka ɲɛ.
Honing processus be baara kɛ cogo min na .
Kɛ: Baarakɛminan (a ka ca a la, a be kɛ silindiri, yɛlɛmani wala jikuru) be siri sɔgɔlan kɔnɔ.
Baarakɛminanw ka baara: Honing minɛn ye .kabakuruwbennin ben mandali dɔ kan. O kabakuruw be bonya ka taga yɔrɔ wɛrɛ walisa ka digi dugukolo kan.
Mosiyɔn:
Rotary motionka honing minan → be tigɛli wale di.
Lamaga min be ɲɔgɔn yɛlɛmaa ka yɔrɔ min be weele ko bore axis → a be tigɛli tilan cogo kelen na.
O tagamasiɲɛw faranin lo ɲɔgɔn kan, o be a .kuruwa-sɛgɛsɛgɛlidugukolo sanfɛ.
Nɛnɛfɛn / tulu: A be yɛlɛma baarakɛyɔrɔ la walisa ka nɔgɔw ta ani ka funteni dɔgɔya.
Minɛnw bɔli: A ka teli ka kɛ, a ka ca a la .0,02 – 0,15 mm, ka geometri ni yɔrɔ ɲuman fisaya k’a sɔrɔ a ma basi yɔrɔw yɛlɛma kosɔbɛ.
Hɔnsɔn ka nafa
Dimensiyɔnw ka tiɲɛtigiya: A be se ka muɲuli kɛ ±2–5 mikɔrɔnw na.
A be se ka kɛ ko a be se ka yɛlɛma yɛlɛma.: A be kuruwa nɔgɔmanw bɔ, minw be tulu{0}}minɛ (Ra 0.1–0.8 μm).
Geometri latilenni: A be taper, ovalité, wavité ani distorsion bɔ minw be to masin wɛrɛw fɛ.
Baara yiriwalen: Crosshatch finish be tulu nɔgɔya ani ka dɔ bɔ yɔrɔ minw be tagama.
A kɔnɔfɛnw ka sii janya: A be dɔ bɔ ɲɔgɔndan na, ka funteni yɛlɛma ani ka dɛsɛ joona.
Vɛrisatilite: A be se ka baara kɛ ni minanw ye minw ka gwɛlɛ, minw ka gwɛlɛ, wala minw be funteni yɛlɛma.
Ligili sɛbɛw
Lizini be kɛ ka caya iziniw kɔnɔ yɔrɔ minw na .dingɛw ni yɔrɔw tigitigian ka ɲi:
Mobili:
Motɛri silindiri woow (ka tulu minɛ ani ka pistɔn sɔgɔli dɔgɔya).
Arbre de vitesse, nɛgɛjuru minw be ɲɔgɔn minɛ, taji pikiriw.
Jii ani fiɲɛminɛfɛnw:
Jii silindiriw ka boonw.
Pump ka soow ni valve farikolow.
Sanfɛlafɛnw:
Aviyɔn ka motɛri yɔrɔ dɔw.
Silindiri minw be jigi.
Ɛnsɛniyeri baarakɛminanw ani baarakɛminanw:
Vitɛsiw, beariw, busiw.
Marifa barigo (min be mɔgɔw lasun u ka ɲɔgɔn minɛ).
Furakɛli minanw ani baarakɛminan tigitigiw.
Lapping ni Honing: Ka danfara minw be u ni ɲɔgɔn cɛ, u faamuya
1. Mun lo be kɛra?
Lapiye ultra-kɛcogo ɲuman ye min be baara kɛ ni .mugu nɔgɔninlap (panti wala yɔrɔ lamini) ani baarakɛminɛn min be se ka yɔrɔw bɔ minw ka nɔgɔ kosɔbɛ ani u be tiɲɛn fɔ.
A be fɛɛn dɔɔni dɔrɔn lo bɔ (mikron kɔnɔ).
A be sinsin .pɛtɛlen, yɔrɔ nɔgɔman, ani janya tilennin.
Tuma caaman na, u b’a jati ko .labanko labanmuguci walima a muguci kɔ.
2. Lapping be baara kɛ cogo min na .
Mugu min be mɔgɔw sɔgɔ: Fɛɛn ɲumanw (aliminiyɔmu, silisiyɔmu wala diaman) be nɔrɔ tulu, tulu wala jii kɔnɔ.
Lap baarakɛminan: Abrasive mugu be don a dakun (nɛgɛ nɔgɔman, zira, wala nɛgɛ nɛgɛman) ani minan yɔrɔ cɛ.
Motion ni ɲɔgɔn cɛ: Lap ni baarakɛminan be tagama cogo kɔlɔsinin na, tuma caaman na, u be tagama kunfɛ wala u be tagama cogo dɔ la min be weele ko figure 8.
Minan bɔli: Abrasive slurry be yɔrɔ misɛnninw tigɛ, ka yɔrɔ dɔ dilan i n’a fɔ filɛrifɛn-.
Tiɲɛn: Ka se ka yɔrɔ labanw sɔrɔ .Ra 0,01–0,05 mani muɲuli minw be sɔrɔ .-mikɔrɔn hakɛ (±0.1–0.5 μm).
3. Lapping ka baarakɛcogow .
Optics & Glass: Lenw, filɛrifɛnw ani prisme.
dɔnniya: Tagamabolow, tilenninya minanw.
Fɛɛrɛw: Pɔnpew ni vannew kɔnɔ, ɲɛda minw be datugu.
Semikonduktɛriw ani kuranfɛnw: Silikɔni fɛnɲɛnamafagalanw, fɛn minw be kɛ ni seramiki ye.
Dɔgɔtɔrɔya minanw: Operelikɛminanw, implants minw be ultra-smooth yɔrɔw ɲini.
4. Ka danfara jɔnjɔnw kɛ Lanadumuni ni hoing cɛ .
| Sawura | limɔgɔ | tun be taga |
|---|---|---|
| Cogo | A be baara kɛ ni kabakuruw ye minw be nɔrɔ ɲɔgɔn na manndreli dɔ kan ani u be yɛlɛma yɛlɛma ani u be yɛlɛma yɛlɛma . | A be baara kɛ ni mugu nɔgɔnin ye min be kɛ ni pilaki ni minan ye . |
| Baarakɛyɔrɔ | Kɔnɔna silindiriki dingɛw (ani kɛnɛma OD honing dɔw) | Fɛɛn minw be yɛlɛma, u be yɛlɛma, wala u tɛ bɛn ɲɔgɔn ma . |
| Minan bɔli | A sanfɛla (0,02–0,15 mm) | A ka dɔgɔ kojugu (mikɔrɔnw) |
| Faranfasiya | A ka ca kosɔbɛ (±2–5 μm) | Janyaba (±0.1–0.5 μm) |
| A sanfɛla ban | A ka ɲi, tulu- . | Mirror- i n’a fɔ a laban (Ra 0,01–0,05 μm) |
| Bilakun | A be geometri latilen (a koorinin, a be yɛlɛmayɛlɛma) + a be boon lɔcogo fisaya | Akili be pɛtɛ, a ka nɔgɔ ani a be se ka yɛlɛma yɛlɛma kosɔbɛ . |
| A ka ca a la | Motɛri silindiriw, jii nɛgɛw, nɛgɛw . | O sababuw, nɛgɛw, jateminɛw, semikonduktɛriw . |
A ka surun:
limɔgɔa ka fisabores silindiri .yɔrɔ min na geometri latilenni + tulu-marali laban ka kan ka kɛ.
tun be tagaka fisayɔrɔ pɛtɛninw wala yɔrɔ minw lamininin lo .minka nɔgɔya kosɔbɛ ani ka tiɲɛn fɔ .minw ka ɲi ka kɛ.
Honing ni Grinding: Danfara jɔnjɔnw n’u ka baarakɛcogo
1. Mugu ye mun lo ye?
Muguciye masin baarakɛcogo dɔ ye min be baara kɛ ni .ka nɛgɛso yɛlɛma .ka fɛɛn dɔ bɔ baarakɛminan dɔ sanfɛ.
A be baara kɛ fɔlɔ ni .a dilan, a bonya ani a labankɛnɛmayɔrɔw walima yɔrɔ pɛtɛninw.
Grinding be se ka muɲu ka muɲu ani ka baara kɛ ka ɲɛ, nka a ka c’a la, a ma kɛ i n’a fɔ honing wala honinging.
2. Baara kɛcogo .
Abrasif nɛgɛ: A be kɛ ni sumanw ye minw be ɲɔgɔn minɛ (aliminiyɔmu oksidi, silikɔni karibidi, CBN, diaman).
Rotari ka tagamasiɲɛ: Sɛgɛsɛgɛrikɛlan be yɛlɛma teliya la.
Baarakɛminanw ka jɛɲɔgɔnya: O nɛgɛso min be yɛlɛma yɛlɛma, o be ɲɔgɔn minɛ ni minan yɔrɔ ye, ka fɛn misɛnninw tigɛ.
balan: A be kɛ ka funteni dɔgɔya ani ka nɔgɔw bɔ.
Minan bɔli: A ka jugu ka tɛmɛ honing kan, k’a ta .0,1 mm ka taga se milimɛtiri caaman ma ., ka kɛɲɛ ni baarakɛcogo ye.
3. Grinding applications .
Mobili & Aerospace: A fɛnw, nɛgɛw, nɛgɛw, tɛrɛnw nɛgɛw.
Minɛnw dilanni: Cutting minanw, saliw, jateminɛw tilenninw.
Nɛgɛbaara: Surface be yɛlɛma ka kɛ pɛtɛnin ye, silindiriki min be kɛ ka yɔrɔw sɔgɔ yɔrɔ koorininw na.
Jɔli ani dilan: Fɛɛn gɛlɛnw tigɛli (seramiki, nɛgɛ gɛlɛn, vɛɛri).
4. Danfara minw be ɲɔgɔn fɛ, olu be ɲɔgɔn cɛ .
| Sawura | limɔgɔ | nanfoni |
|---|---|---|
| Cogo | A be baara kɛ ni kabakuruw ye minw be yɛlɛmayɛlɛma + yɛlɛmayɛlɛma | A be baara kɛ ni nɛgɛso ye min be yɛlɛmayɛlɛma . |
| Minɛnw bɔli | A ka dɔgɔ kosɔbɛ (0,02–0,15 mm) | A ka bon (0,1 mm ka taga se milimɛtiri caaman ma) |
| Faranfasiya | A ka jan kosɔbɛ (±2–5 μm) | A ka bon (±5–10 μm) |
| Surface Finsh | A ka ɲi, kuruwa-sɛgɛsɛgɛra, tulu-minɛ (Ra 0.1–0.8 μm) | Smooth, siratagama (Ra 0,2–1,6 μm) |
| Baarakɛyɔrɔ | Kɛrɛnkɛrɛnniya la, kɔnɔna silindiriki dingɛw (kɛnɛma fana yɔrɔ dɔw la) | Kɛnɛma silindiri, yɔrɔ pɛtɛnin, walima yɔrɔ minw tɛ bɛn . |
| Bilakun | Geometri latilenni (kopi, ovali, tilenninya) + tulu yiriwali | Ka yɔrɔw sɔgɔ, k’u bonya ani k’u yɔrɔ bɛɛ ban . |
| A ka ca a la | Motɛri silindiriw, jii nɛgɛw, nɛgɛw . | Arbres, bearings, vitesses, pilaki pɛtɛninw |
ka surunya:
Mugucika fisaminan caaman bɔliani ka kɛnɛmayɔrɔw labɛn.
limɔgɔka fisaa ka se ka baara kɛ ka ban., ka geometri latilen, ani ka tulu sɔrɔ-} .
Honing ni Burnishing: Danfara jɔnjɔnw n’u ka baarakɛcogo
1. Mun lo ye Burnish ye?
Jeniye yɔrɔ-bancogo ye min na baarakɛminan gɛlɛn, nɔgɔman (a ka ca a la, nɛgɛkuru wala bɔlɔ) be digi baarakɛminan dɔ kan ka .ka yɛlɛma i n'a fɔ plastikibololafɛnw.
Sanni i ka fɛɛn dɔw tigɛ wala k’u bɔ, i ka .A be sɔgɔsɔgɔ ani k’a nɔgɔyɔrɔw be yɛlɛma ka kɛ kuluwo ye.
A be yɔrɔ min be se ka yɛlɛma, a ka gwɛlɛ ani a be se ka fanga don a la k’a sɔrɔ a ma chips bɔ.
2. Baara be kɛ cogo min na .
Baarakɛminanw ka ɲɔgɔn minɛ: A be se ka kɛ ko a be yɛlɛma wala a be se ka yɛlɛma.
Kunnafoniw ni tagamacogo .: N’o minan be tagamana ka tɛmɛ yɔrɔ sanfɛ, fanga min be yɔrɔ sanfɛ, o be yɔrɔ nɔgɔninw yɛlɛma cogo dɔ la.
Kɔgɔjidacogo yɛlɛmani: Peaks be pɛtɛ ka kɛ kuluwow ye → yɔrɔ be nɔgɔya, a ka gwɛlɛ, ani a be yɛlɛma ka kɛ yɔrɔ ye-}resant.
Minɛn bɔli tɛ: A tɛ i n’a fɔ honing, .yɔrɔ sanfɛla digi ani k'a nɔgɔyaka kɛ.
3. Burnishing ka baarakɛcogo .
Mobili: Daɲɛw, sinkpinw, pisitɔn berew.
Jii ani fiɲɛminɛfɛnw: Silindiri min be se ka yɛlɛma, pɔnpew.
Sanfɛlafɛnw: Jigiyɔrɔ yɔrɔw, tɛrɛnw nɛgɛw.
Ɛnsɛniyeri baara: Bearing zurunaliw, nɛgɛjuruw, furakɛlifɛnw.
Nafa jɔnjɔnw: A be sɛgɛsɛgɛri fanga, nɔgɔ fanga, ani yɔrɔ min be se ka yɛlɛma (o be se ka Ra < 0,1 μm sɔrɔ).
4. Danfara jɔnjɔnw cɛ minw be sɔrɔ Hɔn ni jeni cɛ .
| Sawura | Honing | aw k'aw nɛni |
|---|---|---|
| Cogo | Tigɛli → a be minanw bɔ . | Plastiki deformasiyɔn → a be yɔrɔ bɛɛ sɔgɔ . |
| Minɛnw bɔli | Ɔnhɔn (0.02–0,15 mm) | Ayi (a ka nɔgɔ ani a be sɔgɔsɔgɔ) |
| Faranfasiya | A ka bon kosɔbɛ, a be geometri latilen (±2–5 μm) | A tɛ geometri latilen, kɛrɛnkɛrɛnniya la, a sanfɛla laban |
| Surface Finsh | Kuruci-sɔgɔnin, tulu-minɛ (Ra 0.1–0.8 μm) | A ka nɔgɔ kosɔbɛ, a be kɛ i n’a fɔ filɛrikɛlan- i n’a fɔ (Ra < 0,1 μm) |
| Surface ka gwɛlɛ | Yɛlɛmaniba si tɛ | A be dɔ fara a ka gɛlɛya kan nɛnɛ sababu fɛ . |
| A ka fisa | Kɔnɔnakow minw be geometri latilenni ɲini . | Yiriw, berew ani yɔrɔ minw mako be gɛlɛya la + u be se ka yɛlɛma |
| Ladilikanw | Motɛri silindiriw, jikuruw, yɛlɛmafɛnw | Suuw, sinkpinw, silindiri berew, sigiyɔrɔw be yen . |
A ka surun:
limɔgɔ= minanw bɔli tiɲɛn na ka geometri latilen ani ka tulu dilan-} 20000 be ban bores kɔnɔ.
Jeni= nɛnɛ- baarakɛcogo min be yɔrɔ sɔgɔ walisa ka dɔ fara gɛlɛya kan ani ka filɛrifɛn dɔ sɔrɔ min be se ka kɛ i n’a fɔ n’i ma minanw bɔ.
Linikɛminanw n’u ka baarakɛcogo .
1. kelen kelen-Pass Honing Tools
Cogofɔli: Baarakɛminanw be tɛmɛ ka tɛmɛ siɲɛ kelen, ka minanw bɔ ni diaman/CBN abrasive bolo ye.
Tagamasiɲɛw: A tɛ se ka kɛ; kelen-Tile tigɛyɔrɔ tigɛli.
Aplikasiyɔnw:
High-vole bɔli.
Jii vannew, taji fiyɛw, motɛri fitininw.
Nafa minw b'a la: Teliyaba, bɛnbaliya, yɛlɛmani wagati dɔgɔyara.
2. Lini minw be se ka yɛlɛma .
Cogofɔli: Kabakuru minw be mɔgɔw sɔgɔ, u be don mandrin dɔ kan min be bonya ka taga se boon kogo ma.
Tagamasiɲɛw: Baarakɛminan be se ka yɛlɛma ka kɛɲɛ ni bonya yɛlɛmaniw ye.
Ladilikanw:
Zenerali-}pripozi, motɛri silindiriw, jii silindiriw, pɔnpew ka soow.
Nafaw: A be se ka baara kɛ cogo caaman na, a be se ka yɔrɔ caaman minɛ ni minan kelen ye.
3. Diamond ni CBN ka ɲɛnamayakɛminanw
Cogofɔli: Ɲɛcisuperbrasive(amanima walima kibiki bron nitride) sanni ka kɛ abrasisiw ye minw be sɔrɔ mɔgɔw fɛ.
Tagamasiɲɛw: A ka gwɛlɛ ka tɛmɛ, a ka baarakɛminanw ka sii ka jan, a ka tigɛli ka teli.
Ladilikanw:
Minɛnw ka gwɛlɛ (fɛɛrɛw, karabidiw, nɛgɛ gɛlɛnw, sanfɛla nɛgɛw).
Lizini minw be kɛ ka ɲɛ i n’a fɔ sanfɛla, furakɛli, taji pikiri kɛcogo.
Nafaw: A be tiɲɛn fɔ cogo dan na, a be mɛn ani a be baara kɛ ka ɲɛ.
4. Plateau sɔgɔli baarakɛminanw .
Cogofɔli: Baarakɛminanw wala kabakuru kɛrɛnkɛrɛnninw minw dilanna walisa ka .yɔrɔ pɛtɛninn’an be nɛgɛkunbɛnnanw bɔ.
Tagamasiɲɛw: A be yɔrɔ nɔgɔman dɔ to yen min ka kuluw ka dun kɔsɔbɛ walisa ka tulu mara.
Ladilikanw:
Motɛri silindiriw (otomatiki, moto, baji).
Fɛɛn minw be se ka yɛlɛma, u ka ɲi ka yɛlɛma dɔɔni ani u be se ka mɛn.
Nafa minw b'a la: A be tulu yɛlɛma, a be dɔ bɔ a kari-in wagati la, a be ɲɛnamaya yɔrɔ dɔ lataga ɲɛ.
5. Burɔsi minw be se ka yɛlɛma (Ball Hones)
Cogofɔli: Nylon wala nɛgɛ fani minw be se ka yɛlɛma ani u kuncɛw be ni bolokuruw ye minw be se ka mɔgɔw sɔgɔ.
Tagamasiɲɛw: A be bɛn ni bore cogoya ye; a be yɔrɔw labɛn sanni ka fɛnw bɔ minw ka gwɛlɛ.
Aplikasiyɔnw:
Desiburuw, saniya ani ka ban.
Fren silindiriw, motɛri yɔrɔ misɛnninw, marifaw, furakɛli tubi.
Nafaw: A sɔngɔ man gwɛlɛ, a ka nɔgɔ ka baara kɛ n’a ye, a ka ɲi ka se ka yɔrɔw sɛgɛsɛgɛ ani ka yɔrɔw sɛgɛsɛgɛ ka ban.
6. Mandrel sɔgɔli baarakɛminanw .
Cogofɔli: Laada honing minan ni .mandɛri- kabakuruw ., min be se ka bonya ka taga boon kɔnɔ.
Tagamasiɲɛw: A be bonya ni geometri latilenni tigitigi di.
Ladilikanw:
Liziniw ka lɔnniyaba.
Mobili kura lɔli, sanfɛlafɛnw.
Nafa minw b'a la: A be se ka la a la, a be tiɲɛn fɔ ani a be baara kɛ n’a ye kosɔbɛ sɛgɛsɛgɛrikɛlanw na minw be yɛlɛmayɛlɛma ani u be lɔ.
Ka baarakɛminan ɲuman sugandi .
N’i be honing minan dɔ sugandira, an ka miiri nin na:
Baarakɛminanw
Aloys gɛlɛmanw, semiki → Diamond/CBN minɛnw.
Nɛgɛ minw be se ka yɛlɛma, nɛgɛ → Kabakuru minw be se ka yɛlɛma wala minw be se ka bonya.
Bore bonya ani sɔngɔ .
Bore misɛnninw → Minɛn kelen - tɛmɛyɔrɔ ɲuman.
Bajiba/yɛlɛmani → Mandili baarakɛminɛnw minw be se ka yɛlɛma.
A cogoya gɛlɛmanw wala a ka debun → bolokuruw minw be se ka yɛlɛma.
Dugukolo laban waajibiyalen
Oil-erew ka ɲɔgɔndan → Plateau honing minɛnw.
Duloki-i n’a fɔ laban → Jaman/CBN kabakuruw ni mugumugu ɲuman.
Deburu / saniya → Burɔsi minw be se ka yɛlɛma.
Dilan hakɛ
-kanba, ɔridinatɛri → - tɛmɛyɔrɔ kelen walima CNC diamant baarakɛminanw.
Volime dɔgɔman/cɛmancɛ, dilanni gɛrɛntɛ → Mandrel baarakɛminanw minw be se ka bonya.
ka surunya:
Dilan teliya ni bɛnbaliya kama→ Minɛn kelen - tɛmɛbaga.
Ka se ka baara caaman kɛ→ Mandali baarakɛminanw minw be se ka yɛlɛma.
Minɛnw gɛlɛnw ani tiɲɛntigiya kama→ Diaman/CBN ka baarakɛminɛnw.
Ka lubrication & a fanba kɛ ɲɛnamaya ye .→ Plateau minanw.
Ka ban ka ban ani ka deburing→ Burɔsi minw be se ka yɛlɛma.
Honing masin sifaw
1. Masini minw be yɛlɛmayɛlɛma
Cogofɔli: Honing spindle ni baarakɛminan be yɔrɔ kelen na .yɛlɛnin.
Tagamasiɲɛw:
A ka ɲi ka kɛ .bores janmanw .(jang-to-dinatɛri hakɛ > 5:1).
Baarakɛminan min be dɛmɛ sɔrɔ yɔrɔ caaman na a janya bɛɛ la.
Operasiyɔn basiginin ka ɲɛsin -dingɛw sɔgɔli ma.
Aplikasiyɔnw:
Marifa barigow.
Jii silindiriw ka boonw.
Pɔnpe janw ka soow.
2. Masini minw be baara kɛ ni jɔɔsi ye
Cogofɔli: O yɔrɔ min be ni honing ye, o be don .lɔnin, ani baarakɛminɛn be bila tilennin na.
Tagamasiɲɛw:
A be dugukolo yɔrɔ dɔgɔya (a ka ɲi ka kɛ cogo min na).
A ka nɔgɔ ka baara kɛbaarakɛminan belebelebaw, girinmanw.
Gravite be dɛmɛ don ka nɛnɛfɛnw bɔ ani ka fɛnɲɛnamafagalanw bɔ.
Ladilikanw:
Motɛriw ka bolow.
Frenw ka silinɛriw.
Gear bores ani konpɛrɛsiyɔnw ka boonw.
3. CNC Honing Masini .
Cogofɔli: Ɔridinatɛri- ye honing masinw labɛn minw labɛnna .ɔridinatɛri ani -tiɲɛn ɲumansɛnɛ.
Tagamasiɲɛw:
Dumuni, sɔgɔli, ani baarakɛminɛnw yiriwali kɔlɔsili yɛrɛma.
Micron- nivo ka tiɲɛtigiya n’a ka segikanni.
A be se ka taper, ovalité ani geometriki fili wɛrɛw latilen.
Aplikasiyɔnw:
Aerospace motɛri kɔnɔfɛnw.
Mobili ka taji sɔgɔlanw ani silindiriw.
Hidrauli ani pneumatique valvew.
4. Masini minw be baara kɛ ni bolo ye
Cogofɔli: A be baara kɛ ni bolo ye, tuma caaman na, a be baara kɛ ni mandri nɔgɔmanw ani kabakuruw ye minw be se ka mɔgɔw sɔgɔ.
Tagamasiɲɛw:
A sɔngɔ ka dɔgɔ ani a baarakɛcogo ka nɔgɔ.
A be baarakɛlaw lo ɲini minw be se baara la koɲuman walisa ka baara kɛ ni tiɲɛn ye.
A be se ka kɛ baara fitinin ye- ka baara wala dilan baara ye.
Aplikasiyɔnw:
Motɛriw dilanyɔrɔw.
Masiniw ni dilanyɔrɔw fitininw-.
Marifaw barigow ani yɔrɔ misɛnninw minw be se ka yɛlɛma.
Tabali teliman
| Masini sifa | Ɲɛyirali / Kɔlɔsili | A ka fisa | Aplikasiyɔnw ka teli ka kɛ |
|---|---|---|---|
| Honing yɛlɛnin | Spindili yɛlɛnin | Bɛgɛn janw, minw ka dun kɔsɔbɛ | Hidrauli nɛgɛw, marifa barigo . |
| Hɔn | Spindle lɔnin | Bore girinmanw/kurunw | Motɛri bolow, yɛlɛmayɔrɔw |
| CNC Hɔnsɔn | Ɔridinatɛri-kɔlɔsira | -kanba, -tiɲɛnba | Aerospace, mobili, jii bolisiraw . |
| Bolola Honing | Bolo/adamadenya . | Small- labɛn, dɔgɔya-cost baara | Baarakɛyɔrɔw, marifaw barigo . |
Masini minw be baara kɛ ni mɔgɔw ye, u sangali ɲɔgɔn ma: yɔrɔ min lɔnin be ani min lɔnin be CNC ani min be baara kɛ bolo la
| Masini sifa | A ka fisa | Baarakɛcogo ɲumanw | Nafa jɔnjɔnw |
|---|---|---|---|
| Horizontal Horizontal | Bɛgɛn janw, minw ka dun kɔsɔbɛ; yɔrɔba | Jii silindiriw, marifa barigow, pɔnpe so janw | A be se ka sigi yɔrɔ min na, a be se ka kɛ ko a be se ka kɛ ko a ka ɲi ka kɛ. a ka ɲi ka Abhi Fine Products janw, minw ka dɔgɔ . |
| Honing lɔnin | Bori girinmanw walima surunw; yɔrɔ suguw | Motɛri bolow, fren silindiriw, vitɛsi dingɛw | Yɔrɔ -} tele; gravité be dɛmɛ don ka Abhi Fine ka fɛnw bɔ yen . |
| CNC ka yɛlɛmani | -tiɲɛn ɲuman, -ba dilanni | Aerospace kɔnɔfɛnw, mobili ka taji pikiri, hydraulique valve . | Otomatiki kɔlɔsili; mikɔrɔn-nivo tiɲɛtigiya; a ka ɲi geometri gɛlɛmanw ma JetCrafted masin tilenninw kama |
| Bolola Honing | Dɔgɔman-hakɛ, sɔngɔ-baara gɛlɛnw | Motɛriw labɛnna kokura, baarakɛyɔrɔ misɛnninw, marifa barigow | Sɔngɔ fɔlɔ min ka dɔgɔ; operatɛri seko- min be bɔ a la; a be se ka baara kɛ ni fɛn fitininw ye- wala dilan baara ye . |
Ka Masini ɲuman sugandi: I ka miiri koɲuman .
1. Baarakɛyɔrɔ bonya ani a ka baara .
Bɛgɛn janw, minw ka dun kɔsɔbɛ: Sumani .masinw minw be yɛlɛma yɛlɛma .ka basigi ani ka tiɲɛn fɔ.
A ka gwɛlɛ wala a ka surun .: Masini minw be baara kɛ ni jɔɔsi yeu ka ɲi ka tɛmɛ u ka dilan cogo n’u ka gɛrɛntɛ kan-}/kɛrɛki bɔli fɛ.
2. Dilan hakɛ
-kanba, -ba mako be tiɲɛtigiya la: CNC ka masinw sɛgɛsɛgɛka otomatiki ni kalite ɲuman di.
Low-voli walima dilan baaraw .: Manual honing masinwu sɔngɔ ka ɲi ani u be se ka yɛlɛma.
3. A ka ɲi ka kɛ ani a be se ka kɛ yɔrɔ minw na, u be se ka kɛ ka ban .
Muɲuli gwɛlɛw ani yɔrɔ ɲumanw: CNC ka honing masinw .ni diaman wala CBN abrasiw ye, o lo ka ɲi.
Ka ban cogo bɛnnin na: Manuel wala honzontal masinw .be se ka bɔ.
4. Yɔrɔ ani wariko gɛlɛyaw .
Yɔrɔ dantigɛnin: Lini masinw .u ka surun ani u be baara kɛ ka ɲɛ.
Budget ka jateminɛw: Manual honing masinwa ka musakaw hakɛ ka dɔgɔ fɔlɔ.
Kuma surun: Ka Masini ɲuman sugandi .
Ka - tiɲɛtigiyaba sɔrɔ, - hakɛ caman bɔli: CNC ka masinw sɛgɛsɛgɛye sugandili ɲuman ye, min be ɔridinatɛri ni mikɔrɔn- hakɛ tilennin di.
Kabi wagatijan, yɔrɔ minw ka jan: Horizontal honing masinw .be basigi di ani u bɛnnin lo o baara ɲɔgɔnw ma.
Bore girinmanw walima surunw kama yɔrɔ surunw na: Lini masinw .u be baara kɛ ka ɲɛ ani u be yɔrɔ-mara.
-kan mankan dɔgɔman walima dilan baaraw kama: Manual honing masinwu sɔngɔ ka ɲi ani u be se ka yɛlɛma.
